Accessories for Hopper Car & Bulk Trailer Gate Openers

If you’re serious about opening and unloading railcars, your Gate Opener — regardless of make or model — needs a serious Drive Fitting. WORKMASTER®’s tapered, 1-piece Drive Fitting is designed to fit every railcar capstan with full contact on all sides.

Part: #33-10013

Covered hopper cars come in a variety of shapes and sizes, and the height of a capstan and the surrounding terrain can vary just as much. WORKMASTER®’s Heavy-Duty Universal Joint can help overcome these height variances.

Part: #33-10090

Opening hopper car slide gates with a completely worn Capstan Barrel is a problem. When the Barrel’s female square is rounded-off, it resists any effort to get a grip with a Gate Opener Drive Fitting. Workmaster offers two solutions to the problem.

Part: #80-10728

Over time, the inside edges of a railcar’s capstan can wear and become rounded. When this happens, opening and unloading a hopper car becomes an inefficient and costly task. WORKMASTER®’s tapered Swage Kit can bring new life to the most worn capstans.

Part: #33-11120

To ensure you’re getting the most out of your Pneumatic Gate Opener and Railcar Pocket Vibrators, your plant’s air system may need some help. WORKMASTER®’s Air Receiver Tanks can deliver the additional compressed air volume your unloading site requires.

Size         Part #           Dimensions(LxWxH)
30 gal     31-32030      38″ x 16″ x 18″
60 gal     31-32060      48″ x 20″ x 22″
80 gal     31-32080      63″ x 20″ x 22″
120 gal   31-32120      68″ x 24″ x 26″
240 gal   31-32240      84″ x 30″ x 33″

To ensure you’re getting the most out of your Pneumatic Gate Opener and Railcar Pocket Vibrators, your plant’s air system may need some help. WORKMASTER®’s Air Receiver Tanks can deliver the additional compressed air volume your unloading site requires.

Size        Part #         Dimensions(WxH)
30 gal      31-33030     16″ x 38″
60 gal      31-33060     20″ x 48″
80 gal      31-33080     24″ x 46″
120 gal    31-33120     24″ x 67″

Stop water and dirt from entering your Gate Opener with WORKMASTER®’s Eliminizer Filter/Dryer with Stand Assembly. This unique Accessory incorporates patented inverse flow technology engineered specifically to remove condensed liquids and dirt from air-lines.

Part: #82-10424

If your Gate Opener is not designed to include an In-Line Lubricator, WORKMASTER®’s FRL Assembly is ideal. The Assembly maximizes tool protection by filtering, regulating, and lubricating your Gate Opener’s air supply.

Part: #82-10330

Designed for the intermittent start / stop operation of Gate Openers and Vibrators, and factory-set to deliver just the right amount of air tool oil, WORKMASTER®’s In-Line Lubricator is the preferred way to supply the lubrication your air-powered equipment needs.

Part: #82-40003

The internal parts of Pneumatic Rotary and
Piston Type Vibrators are subject to severe
stress and require a special type of lubrication. WORKMASTER®’s VIBRA-LUBE Vibrator Oil is uniquely formulated to coat and protect a vibrator’s inner lining and moving parts.

Part:
1 qt #36-21020 | 1 case (12 qts) #36-21024

Keep your Gate Opener running up to three times longer and cleaner, with less downtime and greater power by using WORKMASTER®’s TOOL-LUBE Air Tool Oil. With regular use of TOOL-LUBE, you can expect greater performance, consistency, and less noise.

Part:
1 qt  #36-21010 | 1 case (12 qts) #36-21016

If your unloading site sees a variety of railcars and you’re constantly changing the accessories on your Gate Opener, you’ll need WORKMASTER®’s Pin & Ring Connector to help keep the job moving. The Pin is hardened steel and the Rink is nick-resistant rubber.

Part: Pin #32-50124 | Ring #32-50000

Ball Valves are an integral part of an unloading site’s air system, unfortunately they’re often overlooked. WORKMASTER®’s Brass Lockable Ball Valves can give you greater, more convenient control over your Gate Opener and Vibrator’s air supply.

Size           Part #
3/8”           81-10002
1/2”           81-10003
3/4”           81-10004
1”               81-10005

WORKMASTER®’s 1-1/2″ Ret-Ring Connector secures your Drive Fitting to your Gate Opener, Extension, or Universal Joint. One piece, molded of durable polyurethane, with a steel insert for added safety, the Ret-Ring Connector makes changing accessories quick and easy.

Part: #32-50001